Influence of thermal distortion on spur gear tooth contact

  1. Dr. Jon Larrañaga 1
  2. Dr. Ibai Ulacia 1
  3. Aurea Iñurritegi 1
  4. Dr. Aitor Arana 1
  5. Jon German 1
  6. Julen Elizegi 1
  1. 1 Mondragon Unibertsitatea
Aldizkaria:
Gear Technology

ISSN: 0743-6858

Argitalpen urtea: 2019

Alea: 36

Zenbakia: 7

Orrialdeak: 70-78

Mota: Artikulua

GOOGLE SCHOLAR lock_openSarbide irekia editor

Beste argitalpen batzuk: Gear Technology

Laburpena

The increase of efficiency in automotive gear transmissionshas been a key subject of research in the past decade (Ref. 1);to this aim, dip-lubricated gearboxes have been designed withminimized oil levels in search of reduced churning powerlosses (Ref. 2) and maximum power-to-weight ratios. However,when such gears’ running conditions reach the highest pitchline velocities and torques, bulk temperatures increase rapidly,resulting in reduced oil film thickness, higher surface shearstresses and an increased number of asperity contacts — allof which may lead to a premature failure of the gear pair.Moreover, in such cases, not only high temperatures are reachedbut also significant temperature gradients are found betweenpinion and gear. Figure 1 shows a sample of the aforementioned operating case. As can be seen, the optimal conditions liebetween a relative immersion depth of H/D=0.1 to 0.25, wherepower losses are minimal. However, with these oil levels thetemperature difference between pinion and gear reach 20°C to30°C because the small size of the pinion results in a lower convection heat transfer due to the reduced oil-lubricated area andits increased rotational speed (with respect to that of the gear)increases the amount of heat flowing inwards, resulting in ahigher bulk temperature of the pinion. This phenomenon leadsto relative pitch deviations and thermally induced profile distortions (Ref. 3).

Erreferentzia bibliografikoak

  • 1. Douglas, C. and A. Thite. “Effect of lubricant temperature and type on spur gear efficiency in racing engine gearbox across full engine load and speed range”, Proceedings of the Institution of Mechanical Engineers, Part J (Journal of Engineering Tribology), 2015,229, pp. 1095–1113.
  • 2. Höhn, B.-R., K. Michaelis and H.-P. Otto. “Influence of Immersion Depth of Dip- Lubricated Gears on Power Loss, Bulk Temperature and Scuffing Load Carrying Capacity,” International Journal of Mechanics and Materials in Design, 2008, 4, pp. 145–56.
  • 3. Sigg, H. “Profile and Longitudinal Corrections on Involute Gears,” SemiAnnual Meeting of the American Gear Manufacturers Association, 1965, Illinois 109.16.
  • 4. Welch, W. P. and J.F. Boron. “Thermal instability in high speed gearing,” Journal of the American Society for Naval Engineers, 1960, 72(3), pp. 471–486.
  • 5. Martinaglia, L. “Thermal Behavior of High-Speed Gears andTooth Correction for Such Gears,” Mechanism and Machine Theory, 1973, 8(3), pp. 293–303.
  • 6. Akazawa, M., T. Tejima and T. Narita. “Full Scale Test of High Speed, High Powered Gear Unit—Helical Gears of 25,000 PS at 200m/s PLV,” ASME Paper No.80-C2/DET-4.
  • 7. Matsumoto, S., Y. Tozaki and M. Fukutomi. “Temperature Distribution in Teeth and Blanks of Ultra High-Speed Gears,” 2001, 1st Report, JSME International Journal, Series C: Mechanical Systems, Machine Elements and Manufacturing, 44, pp. 203–209.
  • 8. Wang, J., “Numerical and Experimental Analysis of Spur Gears in Mesh,” 2003, Ph.D. thesis, Curtin University of Technology.
  • 9. Kashyap, S., D.R. Houser, Z. Smith, S. Selvaraj, J.M. Casella and J.J. Bradway. “Methods of describing plastic gear geometry after a temperature change with application to the prediction of gear load distribution”, 2011, Proc. of the ASME 2011 Design Engineering Technical Conference, Washington, 8, pp. 497–505.
  • 10. Singh, P. K. and A.K. Siddhartha Singh. “An Investigation on the Thermal and Wear Behavior of Polymer-Based Spur Gears,” 2018, Tribology International, 118, pp. 264–272.
  • 11. Arana, A., A. Iñurritegui, J. Larrañaga and I. Ulacia. “Influence of Thermal Distortion on Load Distribution, Transmission Error and Premature Contact,” 2018, Proc. of the International Gear Conference, Lyon.
  • 12. Iñurritegui A., A. Arana, M. Hernandez, J. Elizegi, I. Ulacia and J. Larrañaga. “Modelizado Bidimensional de Engranajes Cilíndricos por Elementos Finitos,” 2018, XXII Congreso Nacional de Ingeniería Mecánica, Madrid.
  • 13. ISO/TR 14179-2:2001 (E). Gears—Thermal Capacity: Part 2. Thermal Load-Carrying Capacity.
  • 14. Litvin, F.L., A. Fuentes, I. Gonzalez-Perez, L. Carvenali, K. Kawasaki and R.F. Handschuh. “Modified Involute Helical Gears: Computerized Design, Simulation of Meshing and Stress Analysis,” 2003, Computer Methods in Applied Mechanics and Engineering, 192, pp. 3619–3655.
  • 15. Dumitrache, P. “On the Control of the Element Finite Meshes with Dimensions in Arithmetic Progression,” 2012, Annals of the University Dunarea de Jos of Galati: Fascicle XIV, Mechanical Engineering, 17 (2), pp. 45–48.
  • 16. MSC Marc 2014. Volume B, Element Library